How can we help? 👋

Creating and mapping meters from Discovered Meters

Review meters Scaler discovers through your integrations and create and map them in one step.

Purpose of this article

When an integration is connected, Scaler automatically discovers meters from it. Discovered Meters lets you create and map each one to Scaler in a single step, instead of creating a meter and mapping it separately.

ℹ️

Discovered Meters is enabled for all integrations.

Before you start

Access required: Admin or Portfolio Editor.


Reviewing discovered meters

  1. Go to Data Collection Portal → Portfolio → Automations → Discovered meters
  1. Each row shows a status: Ready to configure, Review ready, Created, or Dismissed
  1. Use the provider filters to see the meter's original values from the provider, and the Scaler filters to see how they map to Scaler fields
  1. Click a meter to open its details panel
How provider fields are mapped to Scaler fields

For ENERGY STAR Portfolio Manager and utility sync, Scaler prefills the draft meter from the provider's meter type. You can change any prefilled value before creating the meter. For other integrations, fill in the meter details yourself before creating the meter.

ENERGY STAR Portfolio Manager

The ESPM meter type sets Resource type, Subcategory and Source (for waste meters also the waste type). Every ESPM meter gets Monitoring method Conventional meter, Data type Consumption recording, and the start date from ESPM.

ESPM meter type
Subcategory
Source
Electric
Off Site Electricity
Grey
Electric on Site Solar
On Site Renewable Electricity
Green (solar)
Natural Gas
Natural Gas
Normal
Propane
LPG (Propane)
Normal
Diesel
Diesel
100% mineral diesel
Fuel Oil No 2 / No 4 / No 5 or 6
Fuel Oil
Matching fuel oil grade
District Steam / District Hot Water
District Steam / District Hot Water
Normal
District Chilled Water
District Chilled Water
Electric Driven Chiller (other chillers left blank)
Municipally Supplied Potable Water
Potable
Indoor or Outdoor, with Percentage indoor 100 or 0
Municipally Supplied Reclaimed Water
Reclaimed
Indoor or Outdoor, with Percentage indoor 100 or 0
Well Water
Disposed / Recycled / Composted / Donated-Reused waste
Non Hazardous (Hazardous for Regulated Medical Waste)
Landfill / Recycling / Compost / Reuse

ESPM is the source of truth for the classification. If you change the resource type, subcategory or source on an ESPM draft, the next sync sets it back to the ESPM value. Your monitoring method is kept.

Utility sync

Service type
Resource type
Subcategory
Source
Percentage indoor
electric, lighting
Energy
Off Site Electricity
Grey
natural_gas
Energy
Natural Gas
Normal
district_heat
Energy
District Heating and Cooling
water
Water
Potable
Indoor
100
irrigation
Water
Potable
Outdoor
0
sewer
Water
sanitation
Waste
Non Hazardous

Every utility sync meter gets Monitoring method Invoice, Data type Consumption recording, and Supplier set to the utility name on the bill. Utility bills carry no green supply or indoor/outdoor data, so Grey and Indoor are defaults. A service type not in this list leaves the classification blank. Utility sync only fills fields you have left blank, so your corrections survive the next sync.


Creating and mapping a meter in one step

  1. Open the meter's details panel
  1. Check the prefilled fields and fill in anything still blank: resource type, subcategory, source, area type, monitoring method, and start date
  1. Click Save and create

This single action creates the meter in Scaler and maps it to the provider meter, so there's no separate mapping step to complete afterward.

💡

Select multiple discovered meters to approve, update, or create + map them in bulk from the table toolbar.


Dismissing a meter

Click Dismiss on a meter you don't want to add. Dismissed meters can be restored later from the Dismissed filter.


Additional resources

Did this answer your question?
😞
😐
🤩